View ICS2510C_114814.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Integrated Circuit Systems, Inc.
ICS2510C
3.3V Phase-Lock Loop Clock Driver
General Description
The ICS2510C is a high performance, low skew, low jitter clock driver. It uses a phase lock loop (PLL) technology to align, in both phase and frequency, the CLKIN signal with the CLKOUT signal. It is specifically designed for use with synchronous SDRAMs. The ICS2510C operates at 3.3V VCC and drives up to ten clock loads. One bank of ten outputs provide low-skew, low-jitter copies of CLKIN. Output signal duty cycles are adjusted to 50 percent, independent of the duty cycle at CLKIN. Outputs can be enabled or disabled via control (OE) inputs. When the OE inputs are high, the outputs align in phase and frequency with CLKIN; when the OE inputs are low, the outputs are disabled to the logic low state. The ICS2510C does not require external RC filter components. The loop filter for the PLL is included on-chip, minimizing component count, board space, and cost. The test mode shuts off the PLL and connects the input directly to the output buffer. This test mode, the ICS2510C can be use as low skew fanout clock buffer device. The ICS2510C comes in 24 pin 173mil Thin Shrink Small-Outline package (TSSOP) package.
Features
* * * * * * * *
Meets or exceeds PC133 registered DIMM specification1.1 Spread Spectrum Clock Compatible Distributes one clock input to one bank of ten outputs Operating frequency 25MHz to 175MHz External feedback input (FBIN) terminal is used to synchrionize the outputs to the clock input No external RC network required Operates at 3.3V Vcc Plastic 24-pin 173mil TSSOP package
Block Diagram
FBOUT CLK0 CLK1 CLK2 FBIN CLKIN PLL CLK3 CLK4 AVCC CLK5 CLK6 CLK7 CLK8 CLK9 OE
Pin Configuration
AGND VCC CLK0 CLK1 CLK2 GND GND CLK3 CLK4 VCC OE FBOUT 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 CLKIN AVCC VCC CLK9 CLK8 GND GND CLK7 CLK6 CLK5 VCC FBIN
24 Pin TSSOP 4.40 mm. Body, 0.65 mm. pitch
2510 C Rev D 06/15/01
ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate.
ICS2510C
ICS2510C
Pin Descriptions
PIN NUMBER 1 2, 10, 14 3 4 5 6, 7, 18, 19 8 9 11 12 13 15 16 17 20 21 22 23 24 PIN NAME AGND VCC CLK0 CLK1 CLK2 GND CLK3 CLK4 OE1 FBOUT FBIN CLK5 CLK6 CLK7 CLK8 CLK9 VCC AVCC CLKIN TYPE PWR PWR OUT OUT OUT PWR OUT OUT IN OUT IN OUT OUT OUT OUT OUT PWR IN IN DESCRIPTION Analog Ground Power Supply (3.3V) Buffered clock output. Buffered clock output. Buffered clock output. Ground Buffered clock output. Buffered clock output. Output enable (has internal pull_up). When high, normal operation. When low, clock outputs are disabled to a logic low state. Feedback output Feedback input Buffered clock output. Buffered clock output. Buffered clock output. Buffered clock output. Buffered clock output. Power Supply (3.3V) digital supply. Analog power supply (3.3V). When input is ground PLL is off and bypassed. Clock input
Note: 1. Weak pull-ups on these inputs
Functionality
INPUTS OE 0 1 AVCC 3.33 3.33 CLK (9:0) 0 Driven OUTPUTS FBOUT Driven Driven Source PLL PLL CLKIN CLKIN PLL Shutdown N N Y Y
Buffer Mode 0 0 0 Driven Driven Driven 1 0 Test mode: When AVCC is 0, shuts off the PLL and connects the input directly to the output buffers
2
ICS2510C
Absolute Maximum Ratings
Supply Voltage (AVCC) . . . . . . . . . . . . . . . . . . . Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . Logic Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ambient Operating Temperature . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . AVCC < (Vcc + 0.7V) 4.3 V GND -0.5 V to Vcc +0.5 V 0C to +70C -65C to +150C
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability.
Electrical Characteristics - OUTPUT
TA = 0 - 70C; VDD = VDDL = 3.3 V +/-10%; CL = 20 - 30 pF; RL = 470 Ohms (unless otherwise stated) PARAMETER SYMBOL CONDITIONS MIN TYP Output Impedance RDSP VO = VDD*(0.5) 36 VO = VDD*(0.5) 32 Output Impedance RDSN Output High Voltage VOH IOH = -8 mA 2.4 2.9 IOL = 8 mA 0.25 Output Low Voltage VOL -26 VOH = 2.4 V IOH Output High Current -37 VOH = 2.0 V VOL = 0.8 V 19 25 IOL Output Low Current 13 17 VOL = 0.55 V 1 Rise Time Tr VOL = 0.8 V, VOH = 2.0 V 0.5 1.4 Fall Time1 Tf VOH = 2.0 V, VOL = 0.8 V 0.5 1.5 Duty Cycle1 Dt VT = 1.5 V;CL=30 pF 45 50 at 66-100 MHz ; loaded outputs 52 Tcyc-cyc Cycle to Cycle jitter1 at 133 MHz ; loaded outputs 39 Absolute Jitter1 Tjabs 10000 cycles; CL = 30 pF 57 Skew1 Tsk VT = 1.5 V (Window) Output to Output 80 Phase error1 Tpe VT = Vdd/2; CLKIN-FBIN -150 40 Phase error Jitter1 Tpe3 VT = Vdd/2; CLKIN-FBIN; Delay Jitter -50 35 Delay Input-Output1 DR1 VT = 1.5 V; PLL_EN = 0 3.3
1
MAX UNITS V V mA mA 2.1 2.7 55 100 75 150 150 50 3.7 ns ns % ps ps ps ps ps ns
0.4 -13.6 -22
Guaranteed by design, not 100% tested in production.
3
ICS2510C
Electrical Characteristics - Input & Supply
TA = 0 - 70C; Supply Voltage VDD = 3.3 V +/-10% (unless otherwise stated) PARAMETER SYMBOL CONDITIONS Input High Voltage VIH Input Low Voltage VIL Input High Current IIH VIN = VDD Input Low Current IIL VIN = 0 V; Operating current IDD1 CL = 0 pF; FIN @ 66M 1 Input Capacitance CIN Logic Inputs CO1 Output Capacitance Logic Outputs
1
MIN 2 VSS-0.3
TYP
0.1 19 140 4 8
MAX UNITS VDD+0.3 V 0.8 V 100 uA 50 uA 170 mA pF pF
Guarenteed by design, not 100% tested in production.
Timing requirements over recommended ranges of supply voltage and operating free-air temperature
Symbol Fclk Parameter Input clock frequency Test Conditions Min. 25 Max. 175 Unit MHz
Input clock frequency 40 60 % duty cycle Stabilization time After power up 1 ms Note: Time required for the PLL circuit to obtain phase lock of its feedback signal to its reference In order for phase lock to be obtained, a fixed-frequency, fixed-phase reference signal must be Until phase lock is obtained, the specifications for parameters given in the switching characteristics table are not
4
ICS2510C
PARAMETER MEASUREMENT INFORMATION
From Output Under Test 30 pF 500
Figure 1. Load Circuit for Outputs
Notes: Figure 2. Voltage Waveforms 1. CL includes probe and jig capacitance. Propagation Delay Times 2. All input pulses are supplied by generators having the following characteristics: PRR 133 MHz, Z O = 5 0 , Tr 1.2 ns, Tf 1.2 ns. 3. The outputs are measured one at a time with one transition per measurement.
Figure 3. Phase Error and Skew Calculations
5
ICS2510C
General Layout Precautions: An ICS2509C is used as an example. It is similar to the ICS2510C. The same rules and methods apply. 1) Use copper flooded ground on the top signal layer under the clock buffer The area under U1 in figure 1 on the right is an example. 2) Use power vias for power and ground. Vias 20 mil or larger in diameter have lower high frequency impedance. Vias for signals may be minimum drill size. 3) Make all power and ground traces are as wide as the via pad for lower inductance. 4) VAA for pin 23 has a low pass RC filter to decouple the digital and analog supplies. C9-11 may be replaced with a single low ESR (0.8 ohm or less) device with the same total capacitance. 5) Notice that ground vias are never shared. 6) All VCC pins have a decoupling capacitor. Power is always routed from the plane connection via to the capacitor pad to the VCC pin on the clock buffer. 7) Component R1 is located at the clock source. Figure 1.
Component Values: C1= As necessary for delay adjust C[7:2]=.01uF C8,C13=0.1uF C[11:9]=4.7Uf R1=10 ohm. Locate at driver R2=10 ohm.
6
ICS2510C
N
c
L
INDEX AREA
E1
E
12 D
A2 A1
A
In Millimeters SYMBOL COMMON DIMENSIONS MIN MAX A -1.20 A1 0.05 0.15 A2 0.80 1.05 b 0.19 0.30 c 0.09 0.20 D SEE VARIATIONS E 6.40 BASIC E1 4.30 4.50 e 0.65 BASIC L 0.45 0.75 N SEE VARIATIONS 0 8 aaa -0.10 VARIATIONS
In Inches COMMON DIMENSIONS MIN MAX -.047 .002 .006 .032 .041 .007 .012 .0035 .008 SEE VARIATIONS 0.252 BASIC .169 .177 0.0256 BASIC .018 .030 SEE VARIATIONS 0 8 -.004
-Ce
b SEATING PLANE
N 24
D mm. MIN 7.70 MAX 7.90 MIN .303
D (inch) MAX .311
aaa C
Reference Doc.: JEDEC Publication 95, MO-153 10-0035
4.40 mm. Body, 0.65 mm. pitch TSSOP (0.0256 Inch) (173 mil)
Ordering Information
ICS2510CG-T
Example:
ICS XXXX y G - PPP - T
Designation for tape and reel packaging Pattern Number (2 or 3 digit number for parts with ROM code patterns) Package Type G=TSSOP
Revision Designator (will not correlate with datasheet revision)
Device Type (consists of 3 or 4 digit numbers) Prefix ICS, AV = Standard Device
ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate.
7

▲Up To Search▲

Price & Availability of ICS2510C

	To Download ICS2510C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .